The ring die as well as the pressing roller of the biomass pellet making maker rotate at a continuous rate, and also the working state of each instant is essentially the same. If the amount of feed material is unmodified, the power usage need to also be reasonably stable, and also the present will certainly be reviewed the electric motor. Likewise reasonably stable.
When the biomass pellet making machine is working, we readjust the feeding amount as long as the product thickness in the feeding area is less than the optimum beginning point of the pressing location, it will directly influence the size of the reliable workplace of the pressing area and journalism location, and trigger the present to stream.
The variation and also the modification of the hourly result of the biomass pellet making device, as well as if the density of the product layer in the feeding location is greater than the optimum beginning point of journalism area, along with enhancing the thickness of the material layer in the feeding location, it will certainly not influence the per hour result as well as power consumption per unit time.
If there is any type of effect, it will certainly no longer trigger adjustments in current and biomass pellet making equipment result. Due to the fact that the density of the product layer in the feeding area goes beyond the maximum beginning factor of journalism zone, the period in between the pressing area and also the pressing zone is constant without any modification. In the interval where the multi-feed product is located, the clamping angle is higher than the vital rubbing angle, and the product will not be squeezed into the pressing location.
Related post: biomass pellet plant
By doing this, with the rise of the feeding amount of the biomass pellet making maker, the equilibrium of in and out is damaged, as well as the in is greater than the out, as well as the product layer in the feeding location is It will collect thicker as well as thicker up until all the voids are filled as well as obstructed to the feed port, so that the biomass pellet equipment can not work typically. Right now, the current will boost.
In the actual job of the biomass pellet making equipment, with the change of the feeding amount, the rapid output and also the current of the primary motor will change appropriately. And also when the feeding thickness does not exceed the maximum beginning point of journalism location, it will not create a growing number of worldly layers in the feeding location due to the rise in the quantity of powder we feed.
As has been said before, the location that can trigger instantaneous outcome as well as power consumption modifications should be the two areas of job as well as product layers - the compression location and also the biomass pellet maker extrusion location, so we believe that the 3rd location discussed over- - The affordable existence of the feeding location has certain conditions.
Related post: 10T/H Biomass Wood Pellet Plant in USA
That is to state, the fed material layer is distributed in the compaction area, the extrusion area and the feeding area whose overall density does not exceed the optimum entrance factor of the compaction location.
The biomass pellet making equipment will work generally under the allowed power. If the quantity is too large as well as surpasses the thickness of the optimum beginning point of the compaction location, the material layer will collect as well as gradually rise, and the biomass pellet making equipment will certainly not work usually. Current is varying.
With the above analysis, let's go over some phenomena showed by the biomass pellet making machine under two feasible working problems:
( 1 )When the power of the major motor is not large sufficient compared with the matching biomass pellet making equipment granulation criteria, the thickness of our feed goes to the end of the extrusion zone and also the maximum entrance factor of the compression zone (this will certainly differ with the raw products, compression proportion, reliable length-diameter ratio, humidity, pressure rollers as well as other variable elements to adjust accordingly), usually will not surpass the maximum beginning point, with the increase of the feeding quantity, the compression location will change appropriately.
Related post: RICHI pellet making machine
The size of the interval will be reduced, and the interval length of the capture area will progressively increase as necessary, and also the current of the primary motor will certainly likewise slowly increase till it gets to the optimum allowed usage. If the present reaches the defense value we set, and also the thickness of the feeding material has actually not exceeded the density of the maximum beginning factor of the biomass pellet device pushing location, if the feeding amount is increased, the safety system will certainly act, and the excess powder will be released. In order to guarantee the typical function of biomass pellets.
( 2 ) Mean the power of the main electric motor is large or the motor falls short to overload after the density of the feeding product goes beyond the thickness of the maximum starting point of journalism location due to the comprehensive changes of several variables. Currently, the powder fed to individuals can not boost the moment outcome, neither will it trigger the boost of the major motor present, yet can only continue to raise the powder stack accumulated in the maker till the inner tooth cavity of the biomass pellet press equipment is blocked.
Cause the biomass pellet making maker to not work effectively. Naturally, this special phenomenon hardly ever occurs in actual manufacturing (if the raw material moisture is also large, the effective facet proportion is too small, the pressure roller is significantly used and the gap is not readjusted properly, the raw material is replaced, etc, this sensation may happen), this is our undesired problems.
Thorough analysis of the very first frequently made use of functioning state, it is simple to know that on the facility that the pertinent conditions are unchanged, with the adjustment of the feeding quantity, the interval size of the compression zone and the extrusion zone is within a specific range Matching changes are additionally made (the feed circulation rate is minimized, the size of the extrusion area is decreased, as well as the size of the compression area is lengthened; otherwise, the extrusion area is prolonged and also the compression area is reduced), and also the feeding quantity does not surpass the stress. When the density of the optimum beginning point of the limited area is concerned, the lengths of the above two intervals are not a constant value when this article is written. The larger the extrusion zone length value, the higher the biomass pellet maker production efficiency and the longer the pellet length per extrusion per roller.
More details:
https://www.pellet-richi.com/wood-pellet-machine/biomass-pellet-mill.html
Therefore, it is concluded that the factors of current instability under the condition of controlling the feeding amount need to be investigated from the moisture content of the raw material, the effective aspect ratio is too small, the pressure roller is severely worn and the gap is not adjusted properly, and the raw materials are replaced.
RICHI MACHINERY has been established for more than 25 years, specializing in biomass pellet making machine for sale, the development and production of single/complete pellet production lines such as animal feed, biomass fuel, wood waste, grass, straw, organic fertilizer, etc, and provide design and services for EPC/Turnkey projects!
For more details: Richi Machinery
Email Address: enquiry@pellet-richi.com
Phone/Whatsapp: 0086-13838389622
